Scopus İndeksli Yayınlar Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.12416/8651
Browse
16 results
Search Results
Article Citation - WoS: 10Citation - Scopus: 12Influence of the Heat Treatment on the Microstructure, Mechanical and High-Temperature Oxidation Behavior of Hastelloy X Alloy Fabricated Via Laser Powder Bed Fusion(Elsevier Science Sa, 2025) Ozer, Seren; Yalcin, Mustafa Alp; Bilgin, Gueney Mert; Davut, Kemal; Esen, Ziya; Dericioglu, Arcan F.The effect of building direction and heat treatment on the microstructure, mechanical properties, and high- temperature oxidation behavior of Hastelloy X (HX) alloy fabricated by the laser powder bed fusion (L-PBF) method was studied. Electron backscatter diffraction analyses revealed that the development of textured columnar grains with varying average grain sizes, boundary fractions, and dislocation densities induced the mechanical anisotropy observed in both horizontally and vertically fabricated samples. The yield strength (YS) values of the horizontally and vertically as-fabricated samples were determined as 605.7 +/- 15.9 MPa and 552.3 +/- 8.5 MPa, respectively. The post-processing heat treatment increased the ductility remarkably and reduced YS value down to similar to 445 MPa for all samples by the elimination of microstructural anisotropy and increased grain size subsequent to recrystallization. Oxidation tests conducted at 900 degrees C up to 100 h on as- fabricated samples exhibited severe intergranular oxidation, which was accompanied by the formation of large voids and microcracks as well as spallation of the oxide layer. In contrast, the heat-treatment improved the oxidation resistance of the alloy possibly due to the formation of uniform and dense Cr2O3 layer on the substrate surface.Article Citation - WoS: 3Citation - Scopus: 3Nanomechanical Properties of Al-Tb Marginal Metallic Glass(Elsevier Science Sa, 2023) Okuyucu, Can; Ulucan, Tolga Han; Abboud, Mohammad; Motallebzadeh, Amir; Ozerinc, Sezer; Kalay, Ilkay; Kalay, Yunus ErenAl-Rare Earth (RE) metallic glasses provide an effective model system to study the effect of nanocrystallites in an amorphous matrix on nanomechanical behavior. In this work, we achieved a series of Al-Tb metallic glasscrystalline composites with systematically varying crystalline content through annealing. The nanomechanical properties were characterized using micropillar compression tests and nanoindentation for as-quenched amorphous and annealed amorphous/nanocrystalline composite specimens. The promising hardness increases after annealing from 3.0 GPa to 4.6 GPa and elastic modulus increment from 68 GPa to 92 GPa were discussed in detail, considering the structural features of Al-RE marginal metallic glass formers. The increase in elastic modulus is associated with the nucleated fcc-Al nanocrystals that divide the amorphous matrix, leading to the branching of the shear bands. The correlation between the fcc-Al nanocrystals and the behavior of shear bands was discussed in detail.Article Citation - WoS: 41Citation - Scopus: 44Effect of Post Fabrication Aging Treatment on the Microstructure, Crystallographic Texture and Elevated Temperature Mechanical Properties of In718 Alloy Fabricated by Selective Laser Melting(Elsevier Science Sa, 2022) Bilgin, Guney Mert; Davut, Kemal; Esen, Ziya; Dericioglu, Arcan F.; Ozer, SerenThe effect of building direction and post fabrication aging treatment on the microstructure, crystallographic texture and high temperature mechanical properties of Inconel 718 (IN718) alloy fabricated by selective laser melting (SLM) method was investigated. After aging, arc-shaped structures seen in as-fabricated samples dis-appeared and converted into a mixture of columnar and equiaxed grains. Nano-sized gamma '' and/or gamma' precipitates were formed upon aging; however, MC type carbides and Laves phase encountered in as-fabricated samples were not dissolved completely after aging. Moreover, aging did not alter the texture ((001)//building direction (BD)) of as-fabricated samples. Mechanical properties of the alloys under tension were influenced by the build direction, aging time and test temperature. As-fabricated samples produced in vertical direction exhibited higher room temperature strengths with lower ductility due to orientation of overlapped prior melt pools. Room temperature tensile test results revealed that peak aging caused a significant improvement in ultimate tensile strength (UTS), from 1066.5 MPa and 998.4 MPa to 1408.5 MPa and 1330.4 MPa whereas elongation values decreased from 27.5% and 32.2% to 19.6% and 23.7% in vertically and horizontally built samples, respectively. Peak-aged samples (aged at 700 degrees C for 8 h) tested at 600 degrees C displayed serrated regions in their stress-strain curves due to dynamic strain aging (DSA). Although strength values of the samples displayed an expected decrease by temperature, ductility of the samples reduced to minimum at temperatures around 700-800 degrees C, which was attributed to intermediate temperature embrittlement.Article Citation - WoS: 4Citation - Scopus: 4Temperature-Dependent Absorption Edge and Photoconductivity of Tl2in2s3se Layered Single Crystals(Elsevier Science Sa, 2013) Ambrico, M.; Ligonzo, T.; Gasanly, N. M.; Guler, I.Temperature variation of indirect band gap of Tl2In2S3Se layered single crystals were obtained by means of absorption and photoconductivity measurements. The temperature coefficient of -7.1 x 10(-4) eV/K from absorption measurements in the temperature range of 10-300 K in the wavelength range of 520-1100 nm and -5.0 x 10(-4) eV/K from PC measurements in the temperature range of 132-291 K in the wavelength range of 443-620 nm upon supplying voltage V = 80 V were obtained. From the analysis of dark conductivity measurements in the temperature range of 150-300 K, conductivity activation energy was obtained as 0.51 eV above 242 K. The degree of the disorder, the density of localized states near Fermi level, the average hopping distance and average hopping energy of Tl2In2S3Se crystals were found as, 1.9 x 10(5) K, Nf = 4 x 10(20) cm(-3)eV(-1), 29.1 angstrom and 24.2 meV in the temperature range of 171-237 K, respectively. Activation energy of hopping conductivity at T = 171 K was obtained as 41.3 meV and the concentration of trapping states was found as 1.6 x 10(19) cm(-3). (C) 2012 Elsevier B.V. All rights reserved.Article Citation - WoS: 8Citation - Scopus: 8Design of Quantum Sensor To Duplicate European Robins Navigational System(Elsevier Science Sa, 2021) Salmanogli, Ahmad; Gokcen, DincerIn this article, we design a quantum device to duplicate the European Robins procedure to precisely deter-mine the migratory route. In the mentioned procedure, the important issue is the geomagnetic field effect on the magnetic momentum of the created radical pairs (triplet-singlet states) dancing with a special fre-quency. To duplicate the procedure, a quantum sensor consisting of two coincident tripartite systems is designed. Each tripartite system is independently excited with the entangled photons (signal and idler). The interesting point is that by manipulation of the system in the right condition, the microwave cavities modes separately affected by the entangled photons can be entangled. The entangled microwave photons play the same role as the triplet-singlet states present in the bird's navigational system. The key point in the design of the quantum sensor is that the entanglement between microwave photons can be strongly affected by the external magnetic field. In fact, this is the criterion employed by the quantum sensor to sense the magnetic field intensity and the direction. To analyze the system, the canonical quantization (or microscopic) method is used to determine the sensor's Hamiltonian, and also the system dynamics equations of motions are analytically derived using Heisenberg-Langevin equations. (c) 2021 Elsevier B.V. All rights reserved.Article Citation - WoS: 62Citation - Scopus: 69Titanium-Magnesium Based Composites: Mechanical Properties and In-Vitro Corrosion Response in Ringer's Solution(Elsevier Science Sa, 2013) Esen, Ziya; Dikici, Burak; Duygulu, Ozgur; Dericioglu, Arcan F.Ti-Mg composite rods exhibiting both bioinert and biodegradable characteristics have been manufactured by hot rotary swaging from elemental powders of titanium and magnesium. As a result of processing, spherical magnesium powders elongated in the direction of deformation and the dendritic structure in starting magnesium powders transformed into highly equiaxed grains. Magnesium particles in the outer layer of the composites were decorated by thin layer of MgO while the interior parts were free from oxides. As expected, Young's moduli, yield and peak strengths of the composites were observed to decrease with an increase in the magnesium content, while ductility of composites was enhanced by decreasing the amount of titanium. Composites fractured at an angle 45 to the loading axis along the titanium particle boundaries and through the magnesium particles via transgranular type of fracture with the accumulation of twins near the fracture surface of magnesium. Mechanical properties of the composites were observed to be comparable to that of bone and the composites exhibited biodegradable and bioinert character upon testing in Ringer's solution such that magnesium was selectively corroded and pores were formed at prior magnesium powder sites while titanium preserved its starting skeleton structure. In addition, it was found that volume ratio of titanium and magnesium, and continuous MgO layer are the most important parameters which should be considered in designing biodegradable magnesium alloys with an appropriate corrosion rate. (C) 2013 Elsevier B.V. All rights reserved.Article Citation - WoS: 20Citation - Scopus: 21The Effect of Processing Routes on the Structure and Properties of Magnesium-Tini Composites(Elsevier Science Sa, 2012) Esen, ZiyaTiNi particulate-reinforced magnesium matrix composites were fabricated by rotary hot swaging and post-annealing heat treatment. The magnesium matrix of the processed composites was observed to contain elongated grains comprised of equiaxed recrystallised grains. Each elongated grain was surrounded by thin, non-continuous magnesium oxide layers composed of nanometric magnesium oxide particles. The TiNi reinforcement particles preserved their starting spherical shape during processing and testing. However, the hot deformation and annealing heat treatment changed the underlying room temperature microstructures and transformation behaviours of the reinforcements. In contrast to the majority of the ceramic reinforcements, the ductility of the composites was not significantly degraded by the addition of TiNi reinforcements; conversely, an approximately 25% enhancement was recorded in the elongation values for the Mg-5 vol% TiNi alloy. While the yield strengths of the composites changed linearly with increasing reinforcement content, the highest compression peak strength value was obtained with the addition of 5 vol% TiNi, beyond which the strength was slightly decreased. During mechanical testing, the TiNi particles debonded due to insufficient bonding between the matrix and reinforcement, and fracture resulted largely within the oxide layers present in the interfacial region and the magnesium oxide film in the magnesium grain boundaries. (C) 2012 Elsevier B.V. All rights reserved.Article Citation - WoS: 32Citation - Scopus: 36Sers-Based Ultrafast and Sensitive Detection of Luteinizing Hormone in Human Serum Using a Passive Microchip(Elsevier Science Sa, 2018) Yildirim, Ender; Eryilmaz, Merve; Selbes, Yesim; Saglam, Necdet; Tamer, Ugur; Gjergjizi, Belma; Cogun, FerahHuman luteinizing hormone (LH) is an important analyte for doping control analysis since it increases the athletic performance. However, traditional methods to detect LH have few disadvantages, such as long analysis duration, waste disposal problem and sample matrix effect. Addressing these problems, surface enhanced Raman spectroscopy based LH analysis using a passive microfluidic chip was developed and optimized. Antibody modified magnetic gold nanoparticles captured the LH and then, 4-aminothiophenol (4-ATP) labeled nanoparticles formed the sandwich immunoassay structure. The complex and the other reactions occurred in different chambers of the chip. The SERS signals of 4-ATP were recorded from the chamber and the system was shown to detect 0.036 IU L-1 in serum samples. The performance of the immunoassay was compared to all other methods and the proposed assay was the fastest analysis of LH without any problems associated with the sensitivity. The shorter analysis time was recorded because the chip enables the control of all reactions in one place and there was no requirement of a specialized laboratory. (c) 2018 Elsevier B.V. All rights reserved.Article Citation - WoS: 5Citation - Scopus: 6Surface Characteristics and In-Vitro Behavior of Chemically Treated Bulk Ti6al7nb Alloys(Elsevier Science Sa, 2017) Ocal, Ezgi Butev; Esen, ZiyaThe effect of various treatments on surface chemical composition and structure, and bioactivity of Ti6Al7Nb bulk alloys has been investigated. The alloys were treated employing aqueous solutions of NaOH and CaCl2 separately, and also by subsequent CaCl2 treatment after NaOH treatment (NaOH-CaCl2 treatment) which were followed by heat treatment. NaOH treatment was observed to be effective in enrichment of surface layer with Na. On the other hand, Na+ ions were mostly replaced by Ca2+ ions as a result of NaOH-CaCl2 treatment, while single step CaCl2 treatment was less effective in Ca incorporation. Additionally, porous network surface structure seen in NaOH and NaOH-CaCl2 treated samples was completely different than globular morphology detected in CaCl2-treated samples in single step. Subsequent heat treatments caused coarsening of surface structure and loss of some Na+ and Ca2+ ions. NaOH and NaOH-heat treated samples did not exhibit apatite formation within 15 days immersion in simulated body fluid (SBF). On the other hand, NaOH-CaCl2 samples had the highest apatite formation; however, NaOH-CaCl2-heat treated samples did not display any mineralization. Conversely, CaCl2 treated samples allowed apatite formation after heat treatment. (C) 2016 Elsevier B.V. All rights reserved.Article Citation - WoS: 50Citation - Scopus: 52Effect of Borotitanizing on Microstructure and Wear Behavior of Inconel 625(Elsevier Science Sa, 2017) Karakas, Mustafa Serdar; Gok, Mustafa Sabri; Kucuk, Yilmaz; Demir, Mehmet; Kanca, Erdogan; Cakir, Huseyin; Gunen, AliInconel 625, a nickel-based superalloy, is used in a wide range of applications including the marine and petroleum industries under where it is subjected to harsh conditions such as high temperatures and highly corrosive environments. However, its wear resistance is limited and can be often considered unsatisfactory in some applications. If this alloy were to be used under abrasive wear conditions, its surface would have to be protected by a wear resistant coating. In this study, a two-step thermo-chemical borotitanizing treatment (including an initial boriding step followed by titanium diffusion) is proposed. Microstructural characterization (optical microscopy, scanning electron microscopy, energy dispersive spectroscopy and X-ray diffraction) and mechanical properties (induding micro-hardness and micro-abrasion wear) of the coated samples were conducted. Microstructural studies revealed a compact, homogenous, silicide-free coating, consisting of four distinct regions: a TiB2 layer, a multi-phase boride layer, a diffusion zone and the substrate. Hardness values were significantly higher than those obtained by standard boriding treatments. Due to the nano-sized bodding agents used, the coatings formed on the surface were thicker than coatings obtained by methods such as nitriding, paste bodding and pack-boriding, and comparable to that of laser boriding. The wear resistance was improved by up to ten times in comparison with untreated Inconel 625. Grooving was the effective wear mechanism in untreated Inconel 625. How-ever the increase in surface hardness achieved by the borotitanizing treatment changed the wear mechanism in the coated samples from grooving to rolling. (C) 2016 Elsevier B.V. All rights reserved.