Mekatronik Mühendisliği Bölümü Yayın Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.12416/255
Browse
44 results
Search Results
Article Citation - WoS: 9Citation - Scopus: 10Effect of Use of Cu-Cr P/M Electrodes on Machining Performance of Electric Discharge Machining(Gazi Univ, Fac Engineering Architecture, 2015) Gulcan, Orhan; Çoğun, Can; Uslan, Ibrahim; Usta, Yusuf; Cogun, Can; Çoʇun, Can; Mekatronik MühendisliğiIn this study, the effect of use of Cu-Cr powder metal (P/M) electrodes on EDM performance outputs, namely material removal rate (MRR), electrode wear rate (EWR), mean and maximum roughness of machined surface (R-a and R-z) and workpiece surface recast layer thickness, was investigated experimentally. The Cu-Cr P/M electrodes produced at different mixing ratios, compacting pressures and sintering temperatures were used to machine SAE 1040 steel. The analyses performed have shown that the electrode material is deposited on to the work surface as a layer and the powder mixing ratio, the compaction pressure and sintering temperature affect the EDM performance outputs.Article Citation - WoS: 4Citation - Scopus: 4Influence of the Material Properties on the Elastic-Plastic Deformation in a Heat Generating Composite Solid Cylinder(Gazi Univ, Fac Engineering Architecture, 2013) Ozturk, Ali; Gülgeç, Müfit; Gulgec, Mufit; Mekatronik MühendisliğiBased on Tresca's yield criterion and its associated flow rule, the elastic-plastic deformation of a centrally heated composite cylinder with fixed ends is investigated by considering the influence of geometric parameters as well as material properties such as yield strength, modulus of elasticity, Poisson's ratio, coefficient of thermal conduction and thermal expansion. In the study, stress, strain and displacement distributions in the composite cylinder made of elastic-perfectly plastic material are derived. Stress distribution and evolution of plastic regions in the composite are presented for different levels of heat generation in the core.Conference Object Fluorescent On-Chip Imager by Using a Tunable Absorption Filter(Ieee, 2017) Arpali, Caglar; Yıldırım, Ender; Yildirim, Ender; Arpali, Çağlar; Arpali, Serap Altay; Arpali, Serap; Makine Mühendisliği; Mekatronik Mühendisliği; Elektronik ve Haberleşme MühendisliğiConference Object High-Throughput Screening of Blood Samples Based on Structured Illumination On-Chip Imaging(IEEE, 2013) Arpali, Serap; Arpali, S.A.; Arpali, Çağlar; Arpali, C.; Coskun, A.F.; Chiang, H.-H.; Ozcan, A.; Mekatronik Mühendisliği; Elektronik ve Haberleşme MühendisliğiWe demonstrate a high-throughput fluorescent on-chip imaging platform, using structured illumination that can rapidly screen large volumes of scattering media such as undiluted whole blood samples (e.g., ~ 0.3-0.7 mL) for detection of fluorescent micro-objects at low concentrations (e.g.,≤50-100 particles/mL). This imaging modality might especially be useful for rare cell applications involving whole blood samples, such as detection of circulating tumor cells. © 2013 OSA.Article A Parametric Study on the Elastic-Plastic Deformation of a Centrally Heated Two-Layered Composite Cylinder With Free Ends(Polish Acad Sciences inst Fundamental Technological Research, 2016) Yalcin, F.; Gülgeç, Müfit; Ozturk, A.; Gulgec, M.; Mekatronik MühendisliğiIn this paper, an elastic-plastic deformation of a centrally heated two-layered composite cylinder with free ends subjected to uniformly distributed internal energy generation within an inner cylinder is studied using Tresca's yield condition and its associated flow rule. Stress, strain and displacement distributions in the composite cylinder made of elastic-perfectly plastic material are derived considering the influence of geometric parameters as well as material properties such as yield strength, modulus of elasticity, Poisson's ratio, coefficient of thermal conduction and coefficient of thermal expansion. Yielding starts at the outer boundary or at the axis corresponding to an 'edge regime' of Tresca's prism in both cases. Propagations of the plastic regions are studied due to an increase of a heat generation.Conference Object Controller Design for Cacc With Time-Varying Communication Delays(Ieee, 2023) Soysal, Gokhan; Schmidt, Klaus Werner; Bingol, HilalCooperative Adaptive Cruise Control (CACC) aims at the safe and comfortable travel of vehicles at short distances in the form of platoons. Hereby, it is generally desired to attenuate disturbances along vehicles in a platoon, which is captured by different string stability conditions. In this paper, we focus on L-infinity string stability. This condition ensures reducing the magnitude of the acceleration signal along the platoon, which helps to avoid actuator saturation and increases driving comfort. Since the performance of CACC is adversely affected by time-varying communication and actuator delays, we develop the first controller design method for L-infinity-string stability, combining the Lyapunov-Krasovskii method and our custom bisection algorithm. Simulation experiments demonstrate the effectiveness of our method.Article Citation - WoS: 4Citation - Scopus: 4String Stability Under Actuator Saturation on Straight Level Roads: Sufficient Conditions and Optimal Trajectory Generation(Ieee-inst Electrical Electronics Engineers inc, 2022) Bingol, Hilal; Schmidt, Klaus WernerThe heterogeneity of vehicles is an important factor when realizing cooperative adaptive cruise control (CACC) in practice. Specifically, it has to be considered that platoons generally consist of vehicles with both different dynamic properties and actuator limits on the engine and braking force, which is expected to have a negative impact on important properties such as string stability. Accordingly, the subject of this paper is the preservation of string stability for CACC in heterogeneous vehicle strings with potential actuator saturation. To this end, the paper formulates a velocity-dependent force bound that enables the derivation of sufficient conditions for preserving string stability during velocity changes of heterogeneous platoons. These conditions are then used for the analytical computation of trajectories for time-optimal velocity changes. The formal results of the paper are supported by an illustrative simulation study.Article Citation - WoS: 7Citation - Scopus: 6Dynamic Flat-Topped Laser Beam Shaping Method Using Mixed Region Amplitude Freedom Algorithm(Springer Heidelberg, 2022) Arpali, Caglar; Arpali, Serap Altay; Altemimi, Mohammed Fawzi; Alsaka, Dina YaqoobA dynamic beam shaping method is proposed for the generation of flat-top beams (FTBs) in the far field. Using the mixed-region amplitude freedom algorithm, this new method is used to design the required phase distribution encoded on a spatial light modulator for the generation of FTB profiles. The characteristics of these new beam shaping methods are used as beam parameters, such as the laser beam size, the beam intensity of square FTBs, and the root-mean-square error (RMSE). Using our proposed method, the theoretical performance of beam intensity shaping is improved to an RMSE < 0.02 with a minimum number of iterations of phase reconstruction. Using the phase hologram of dynamic beam shaping, theoretical and experimental comparisons of edge steepness and plateau uniformity were established for the square FTBs of variable beam sizes. It is shown that the dynamic beam shaping of FTBs can produce high intensity uniformity in the plateau region with steep edges, which makes it an effective tool, especially for laser machining applications.Article Citation - WoS: 6Citation - Scopus: 6Design and Implementation of an Electrode Feed Rate Control System in the Electrochemical Drilling Process(Springer Heidelberg, 2022) Cogun, Can; Ozerkan, Haci BekirThe interelectrode gap distance control is essential for preventing short circuit and spark discharge occurrences in the machining gap and ensuring a constant distance between the tool electrode (shortly electrode) and the workpiece throughout the electrochemical drilling (ECD) process. In this study, a gap distance control system was designed and implemented in the constructed ECD machine tool. The gap distance control strategy was based on the machining current's discrete measurement (in microsecond intervals) and changing the gap distance according to a set current value by feeding the electrode towards the workpiece or retracting it during the ECD process. The small diameter deep hole ECD experiments were conducted using 0.5 mm diameter side insulated tubular rotational electrodes with through-hole electrolyte flushing to drill Hadfield and AISI 1040 steels. The experimental results demonstrated the success of the developed control system in ECD operations yielding uniform hole geometries and smooth hole surfaces. The use of the control system eliminated the undesirable formations of spark discharges and short circuit pulses.Article A comparison of iterative Fourier transform algorithms for image quality estimation(Optical Soc Japan, 2018) Alsaka, Dina Yaqoob; Arpali, Çağlar; Arpali, Serap AltayA comparison was established between two iterative Fourier transform algorithms (IFTAs), such as the original Gerchberg–Saxton (GS) and the mixed-region amplitude freedom (MRAF) algorithms, for the hologram reconstruction of different target images through the full reference image quality estimation (IQE) and pixel homogeneity in the Fourier plane presented theoretically and experimentally. The comparison was applied depending upon both algorithms based on a computer-generated hologram (CGH) implemented utilizing a reflective phase-modulated liquid-crystal spatial light modulator (LC-SLM) to obtain the digital kinoform holograms of the desired intensity distributions. These digital holograms were applied to reconstruct the intensity patterns for 852 nm, which represents a laser beam source. The theoretical and experimental results of the reconstructed patterns obtained using the MRAF algorithm were found to be smoother and better than the patterns obtained using the GS algorithm. Unmodulated light beam (dc term) is removed from the reconstructed patterns attributed to digital kinoform holograms of MRAF algorithm as an alternative to the theoretical and experimental results without using any additional optic equipment at the light path. Moreover, this paper discussed the full reference objective quality estimations, such as mean square error (MSE), peak signal-to-noise ratio (PSNR), structural content (SC), normalized absolute error (NAE), normalized cross correlation (NK), and homogeneity of pixels, through the contrast (Cont) and inverse difference moment (IDM) for numerical and experimental results. According to the two desired intensity distributions processed theoretically and experimentally, the results of MRAF algorithm were found to be in the highly accurate recovered phase, the quality of image was enhanced, and the dc term was decreased. Image quality estimation of full reference objective relay on the feedback algorithms experimental attestation has not been implemented yet.