WoS İndeksli Yayınlar Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.12416/8653
Browse
3 results
Search Results
Article Citation - WoS: 1Numerical Analysis of Pulsating Circular Impinging Laminar Jet on a Planar Disc(Turkish Soc thermal Sciences Technology, 2017) Kahroba, Mitra; Türkoğlu, Haşmet; Turkoglu, Hasmet; Makine MühendisliğiIn this study, the flow and heat transfer characteristics of pulsating circular air jets impinging on a flat surface were numerically analyzed. The jet velocity pulsated in time. The objective of the work is to investigate the influence of the jet Reynolds number, pulsation amplitude and pulsation frequency on the rate of heat transfer from the target hot surface. For the analysis, a computer program, based on the control volume method and SIMPLE algorithm, was developed. Laminar flow with the time averaged jet Reynolds numbers between 300 and 700 were analyzed. The pulsation amplitude is ranged between 0.0V(0) (steady jet) and 0.8V(0) (m/s) (V-0 is period averaged jet velocity), and the frequency is ranged between 1 and 6 Hz. The nozzle-to-plate distance was kept constant at H/d=3. From the simulation results, it was observed that at any instant of the pulsation period, the local Nusselt number is maximum at the stagnation point, and it decreases along the plate. This decrease in the local Nusselt number is not monatomic as in the steady jet cases. It has local maximum and minimum values (fluctuations) due to the moving recirculating flow regions along the bottom plate. At low frequencies, the time (period) averaged stagnation point Nusselt numbers are lower than the corresponding steady jet Nusselt numbers. However, with the increasing frequency, the stagnation point Nusselt number increases and become higher than the steady jet Nusselt number.Article Citation - WoS: 2Citation - Scopus: 2Analysis of Heat Transfer Enhancement in Tubes With Capsule Dimpled Surfaces and Al2o3-Water Nanofluid(Turkish Soc thermal Sciences Technology, 2022) Ibrahim, Mahmoud Awni A. Haj; Turkoglu, Hasmet; Yapici, Ekin Ozgirgin; Haj Ibrahim, Mahmoud Awni A.This study aims to numerically investigate and evaluate the enhancement of heat transfer by new capsule dimples on tube surfaces for flow of water and Al2O3-water nanofluid with different concentrations, under uniform surface heat flux. The originality of this work lies in combining two passive heat transfer enhancement methods such as geometrical improvements and nanofluids together. Capsule dimples with different depths were considered. Al2O3- water nanofluid was modeled as a single-phase flow based on the mixture properties. The effects of dimple depth and nanoparticle concentrations on Nusselt number, friction factor and performance evaluation criteria (PEC) were studied. Numerical computations were performed using ANSYS Fluent commercial software for 2000-14000 Reynolds number range. It was found that when laminar, transient and fully developed turbulent flow cases are considered, increase in the dimple depth increases the Nusselt number and friction factor for both pure water and Al2O3-water nanofluids cases. Also, the friction factor increases as dimple depth increases. Results show that increase in PEC is more pronounced in the laminar region than in the transition region, it starts to decrease for turbulent flows. For nanofluid, PEC values are considerably higher than pure water cases. The variation of PEC for capsule dimpled tubes are dependent on flow regimes and dimple depths. Increasing the nano particle volume concentration and dimple depth in laminar flows increase the PEC significantly.Article Citation - WoS: 4Citation - Scopus: 8The Performance of Water Jet Pumps and Their Application in Slurry Transportation(Turkish Soc thermal Sciences Technology, 2023) Kokpinar, Mehmet Ali; Gogus, MustafaThis present work is focused firstly on an experimental investigation for the optimum design of water jet pumps to be used in the hydrotransport of solid particles through pipeline systems. Experiments were conducted in a closed test loop using five types of jet pumps with various dimensions of the driving nozzle, suction nozzle, mixing chamber, and diffuser employing water as driving and suction fluid. The efficiency of each water jet pump element was analyzed and interpretations of results related to each water jet pump were made about the parts to be considered in the optimum design of a water jet pump. From the experimental results, the water jet pump having the optimum mixing chamber, suction nozzle, driving nozzle location, and cross-sectional dimensions produced a maximum efficiency of about 33%. In the second part of the study, the solid particle carrying capacity of water jet pumps in a pipeline system was studied under saltation, moving bed, and heterogeneous flow regimes by introducing seven different types of solid particles having various concentrations into the closed test loop. The effect of jet pumps on separating solid particles from flow in a region was investigated. A curved form of a by-pass system called the 'flow division unit' was added to the main pipeline system and through the flow division unit, then most of the solid particles in the flow were forced to flow towards the suction pipe of the jet pump. As a result of this, only water with very small particle concentrations passed through the centrifugal pumps, and in this way, the wear risk of the centrifugal pump was reduced considerably.