Çankaya GCRIS Standart veritabanının içerik oluşturulması ve kurulumu Research Ecosystems (https://www.researchecosystems.com) tarafından devam etmektedir. Bu süreçte gördüğünüz verilerde eksikler olabilir.
 

Design and analysis of an overconstrained manipulator for rehabilitation

dc.contributor.author Aldulaimi, Hassan
dc.date.accessioned 2015-11-10T08:39:20Z
dc.date.available 2015-11-10T08:39:20Z
dc.date.issued 2015
dc.department Çankaya Üniversitesi, Fen Bilimleri Ensitütüsü, Makine Mühendisliği Bölümü en_US
dc.description.abstract A parallel manipulator is a closed loop kinematic chain mechanism that is attached to the base by at least two limbs in parallel. Compared with the serial, the parallel manipulator has higher load-carrying capacities, higher accuracy, higher stiffness and lower inertia. Due to these advantages the parallel manipulator become viable alternative for wide applications, therefore it have been the subject of study of many research during the recent three decades. However, these kinematic closed loops also have some disadvantages, such as limited workspace, complicated forward kinematics, high cost and complicated structures. To overcome these disadvantages parallel manipulators with less than 6-DoF can be used. Also, designing a parallel manipulator with less than six degree of freedom for a subspace can relatively reduce the complexity.This thesis deals with one of the applications of parallel manipulator as a rehabilitation robot. This device is an over –constrained parallel manipulator 5 degree of freedom with 3 legs. This manipulator consists of a moving platform which is connected to a fixed base via three legs. Each leg is made of RRR(RR) (revolute) joints where the first three joint in all legs are parallel and the recent two joint are intersecting .Inverse kinematics of this device including position velocity and acceleration are studied. In addition, the workspace of the parallel manipulator is analyzed. A design optimization is conducted for the prescribed workspace of the device. Finally, this thesis also deals with the dynamic modeling the manipulator using an approach of the principle of virtual work. The equations of motion of the manipulator are derived by considering its motion characteristics. To reduce computations, inverse Jacobian matrices for manipulators are derived to give relations between input and output variables. en_US
dc.description.abstract Paralel manipülatörler yere birkaç bacak ile bağlanan sistemlerdir. Seri manipülatörler ile karşılaştırıldığında daha yüksek yük taşıma kapasitelerine, daha yüksek hassasiyet değerlerine, yüksek dayanım ve düşük eylemsizliğe sahiptirler. Bu özellikleri sayesinde paralel manipülatörler birçok alanda kullanılmaktadır ve ayrıca son 30 yıldır birçok araştırmalara konu olmaktadır. Ancak paralel manipülatörlerin kısıtlı çalışma alanı karmaşık düz kinematik hesapları, yüksek maliyet ve karmaşık yapıya sahip olma gibi bazı dezavantajları da mevcuttur. Bu dezavantajların üstesinden gelebilmek için alt serbestlikten daha düşük sayıda serbestlik içeren manipülatörlerin çalışılmasına hız verilmiştir. Özel bir alt uzay için tasarlanmış bir manipülatör sistemin karmaşıklığını düşürecektir. Bu tezde paralel bir manipülatörün rehabilitasyon amacı ile tasarımı ve analizi gerçekleştirilmiştir. Önerilen sistem beş serbestlikte ve yere 3 bacaktan bağlanmaktadır. Her bir bacak RRR(RR) yapılandırmasına sahiptir. Bütün vii bacaklardaki ilk üç mafsal birbirine paralel iken son iki mafsallar eksenleri çakışacak şekilde yerleştirilmiştir. Verilen pozisyon hız ve ivme değerlerine göre motor pozisyon hız ve ivme değerlerinin hesaplanması için ters kinematik yöntemler kullanılmıştır. Ek olarak sistemin çalışma alanı analizi yapılmış ve optimum bir sonuç elde edilmiştir. Son olarak edimsiz iş prensibi kullanılarak sistemin dinamik modellemesi yapılmıştır. Hesaplamaları kolaylaştırmak adına sistemin Jacobi matrisleri ortaya çıkarılmıştır. en_US
dc.description.publishedMonth 4
dc.identifier.citation ALDULAİMİ, H. (2015). Design and analysis of an overconstrained manipulator for rehabilitation. Yayımlanmamış yüksek lisans tezi. Ankara: Çankaya Üniversitesi Fen Bilimleri Enstitüsü en_US
dc.identifier.uri https://hdl.handle.net/20.500.12416/372
dc.language.iso en en_US
dc.rights info:eu-repo/semantics/openAccess en_US
dc.subject Rehabilitation Robotics en_US
dc.subject Overconstrained Manipulators en_US
dc.subject Workspace analysis en_US
dc.subject Dynamics Analysis en_US
dc.subject Rehabilitasyon Robotları en_US
dc.subject Kısıtlı Manipülatörler en_US
dc.subject Çalışma Alanı Analizi en_US
dc.subject Dinamik Analiz en_US
dc.title Design and analysis of an overconstrained manipulator for rehabilitation tr_TR
dc.title Design and Analysis of an Overconstrained Manipulator for Rehabilitation en_US
dc.title.alternative Rehabilitasyon için Kullanılacak Bir Kısıtlı Manipülatörün Tasarımı ve Analizi en_US
dc.type Master Thesis en_US
dspace.entity.type Publication

Files

Original bundle

Now showing 1 - 1 of 1
Loading...
Thumbnail Image
Name:
Aldulaimi,Hassan.pdf
Size:
30.25 MB
Format:
Adobe Portable Document Format
Description:
Yazar sürümü

License bundle

Now showing 1 - 1 of 1
No Thumbnail Available
Name:
license.txt
Size:
1.71 KB
Format:
Item-specific license agreed upon to submission
Description: